Download >> Download Tranx 160 manual Read Online >> Read Online Tranx 160 manual Amb Tranx 160 Transponder Manual. ZOOM TECHNOLOGY TRANX2000 TRANSX 2000 TRANS X. Mar 10, 2013 How to fix a dead AMB MyLaps transponder (AMB Tranx160 / MyLaps. Battery for 'new style' MyLaps/AMB transponders. 'New style' Yellow TranX 160. This guide only fix problems with a dead battery. And only on the 'new style' Transponders with rounded edges. The old square style transponders with the four screws in the corners uses different batteries! Amb Transponder Ebay- Use a heat gun to rapidly heat up the white glue for faster and easier removal of the dead battery. Be careful not to apply too much heat as the plastic casing will start to melt! After you have soldered in the new battery, AND CHECKED that it fully charges (could take up to 24 hours or more depending on the capacity of the new battery), then use tape to fit the piece of yellow casing you cut off earlier to the transponder casing. Now use a hot glue gun to fill the empty space around the battery with glue. Fix the black end-cap and glue it all together. Fix it with clear tape or duct tape. After it cools down remove tape and check if everything looks and works fine. Be VERY careful not to cut your self with the Stanley knife! And also not to burn your fingers on the hot-glue! Disclaimer: I will take no responsibility if you screw up your transponder or mess up anything. Or if the transponder doesn't work afterwards. If you're not sure how to do this or not willing to risk damaging your transponder, please use Google to search for a professional AMB MyLaps transponder repair service company. There's one in the UK and also in Australia. Feel free to ask any questions regarding this DIY guide though.;) Battery for 'new style' MyLaps/AMB transponders (shown in this video): 'New style' Yellow TranX 160: OEM: NiMH 1.2V 1250mAh Replace with: NiMH 1.2V 2200 mAh AA for extended usage. 'New style' Red TranX 260: Replace with: NiMH 1.2V 2700 mAh AA for extended usage - - - - - Batteries for 'old style/square' transponders (not shown in this video): 'Old style' Yellow TranX 160: OEM: 3.6V 400mAh NiCd (3 x 1/3 AA 300 mAh with pins) 'Old style' Red TranX 260: OEM: 3,6V 450mAh NiCd (3 x 1.2V 450mAh prismatic cells) Thanx for watching! RENTAL KARTING TIMING SYSTEMS The karting timing system is the heart of every karting center. That’s why it is essential to have reliable hardware. Transponders allow the registration of accurate lap times. ![]() Shin sangoku musou eiketsuden. This is essential equipment for your timing system. When the transponder passes the detection loop, it sends information to the decoder. Then, this device transforms data into useful information that the timing software can read. The live timing can be displayed on,,, etc. The transponders of both systems described below don’t need to be recharged: just fix them on your chassis and that’s it! AMB MyLaps hardware The AMB MyLaps timing system is the most used rental karting lap timing equipment in the world. This timing system includes: • 1 timing transponder/go-kart • 1 decoder (connected to the pit PC via COM port or Ethernet) • 1 active loop antenna, 1 coax cable, 1 loop power adaptor Kart Timer hardware Smart alternative for timing solutions on indoor and outdoor tracks. Long lifecycle up to 10 years! No charging needed. This timing system includes: • 1 timing transponder/go-kart • 1 decoder (connected to the pit PC via USB) • 1 loop antenna, 1 loop power adaptor Competition karting timing AMB MyLaps hardware The AMB MyLaps TranX 160 transponder has been developed for competition karting races. Competition drivers can buy their own transponder from your karting center and easily fix it to their go-karts.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |